Let's "Labor" to build the right knife!!

The RANDALL KNIFE FORUMS

A place where EVERYBODY is welcome to join in on the discussion of Randall Made knives

You are not logged in. [Log In] Knifetalk Forums » Forums » Randall Knife Talk » Randall Made Knives » Let's "Labor" to build the right knife!!

Page 11 of 33

Topic Options

Rate This Topic

#183201 - 09/05/19 11:40 PM Re: Let's "Labor" to build the right knife!! [Re: LarryWW1246]
Sharpi Knife Enthusiast Registered: 12/01/15 Posts: 645	A SharpI
Top

#183202 - 09/05/19 11:59 PM Re: Let's "Labor" to build the right knife!! [Re: Sharpi]
Kirko Knife Enthusiast Registered: 12/01/13 Posts: 454 Loc: Ladue,Missouri	B
Top

#183209 - 09/06/19 08:23 AM Re: Let's "Labor" to build the right knife!! [Re: Kirko]
Captain Chris Stanaback Knife Enthusiast Registered: 09/14/05 Posts: 12867 Loc: Central Florida	Right now it's all tied up @ 9 votes each. I'll give this until tonight and let's see where we are. Granted, I didn't ask for the roll call vote but, nonetheless, we're tied at this point! Vote, if you haven't. Thanks, Capt. Chris _________________________ Capt.Chris Stanaback RKCC/RKCA Founder RKS #016 NRA Lifetime Member CAPTSTANABACK@aol.com WEBSITE: www.captstanaback.com
Top

#183210 - 09/06/19 08:42 AM Re: Let's "Labor" to build the right knife!! [Re: Captain Chris Stanaback]
LarryWW1246 Knife Enthusiast Registered: 03/20/06 Posts: 1856	The old saying is "Vote early and often." Larry _________________________ Larry W. Williams RKCC #CM-041 ABKA #046 RKS #1246
Top

#183211 - 09/06/19 10:32 AM Re: Let's "Labor" to build the right knife!! [Re: LarryWW1246]
Duke Knife Enthusiast Registered: 08/21/09 Posts: 2004 Loc: Southwest Virginia	A) all the way _________________________ Duke;RKS#5567 RKCC-CM-087 Southwest VA
Top

#183215 - 09/06/19 11:20 AM Re: Let's "Labor" to build the right knife!! [Re: Duke]
JE6245 Knife Enthusiast Registered: 01/02/14 Posts: 1064 Loc: Tallahassee FL	Sure looked like a roll call vote to me but .... consensus opinion among folks I know (especially my wife) is that I don't know my butt from a hole in the ground. _________________________ Jim E. “If you don’t know where you are going, you might wind up someplace else.” – Yogi Berra Me 2020
Top

#183217 - 09/06/19 11:42 AM Re: Let's "Labor" to build the right knife!! [Re: JE6245]
Eric Knife Enthusiast Registered: 11/18/15 Posts: 1668 Loc: Michigan	A _________________________ Eric
Top

#183220 - 09/06/19 01:22 PM Re: Let's "Labor" to build the right knife!! [Re: Eric]
Shoot870p Knife Enthusiast Registered: 01/12/17 Posts: 1521	I did not think we were at the vote stage yet but it seems I was wrong. I vote: A8-4 knives Walker _________________________ Shoot870p
Top

#183230 - 09/06/19 06:20 PM Re: Let's "Labor" to build the right knife!! [Re: Shoot870p]
Robert Frey Knife Enthusiast Registered: 06/07/11 Posts: 1544 Loc: Wausau, WI USA	B) RMK Model "GTR" & "DENMARK SPECIAL" _________________________ Rob Frey NRA Life Member
Top

#183286 - 09/09/19 06:25 PM Re: Let's "Labor" to build the right knife!! [Re: Robert Frey]
JerryG Knife Enthusiast Registered: 11/04/11 Posts: 327 Loc: WI	B) RMK Model "GTR" & "DENMARK SPECIAL" _________________________ Jerry
Top

Page 11 of 33

Hop to:

Moderator: Mr_Mod